To extend/retract the Lippert High-Speed Power Stabilizer Jack # LC298707 you will need to press and hold the the switch, as there is no automatic cut off.
However, this jack does have an integrated circuit breaker to protect you from damaging your RV by tripping the breaker if the circuit is overloaded while lifting the trailer.
I have included a review video as well for you to check out as well. view full answer...
Yes, the Kodiak XL ProLube Kit for 3500-lb Axles part # XLPROLUBE1980KIT is compatible with spindles that have grease/zerk fittings in the ends or otherwise known as EZ-Lube. If you wish, you can remove the fittings but they will still fit with the fittings in place regardless. The fittings are either threaded on or pressed in. view full answer...
I went ahead and checked out the owner's manual for the Jensen RV Stereo w DVD Player - Double DIN - App Control # JWM60A and the radio turns on but isn't putting out any sound then you'd need to do the following:
-Make sure that the volume, fader/balance, and mute controls are set correctly,
-Verify that the proper speakers are selected,
-Verify that the speakers are connected properly,
-Check your wiring for any open circuits on your speaker wires,
Finally, if everything looks good... view full answer...
Hey Rad, it comes down to what the door threshold height is of your camper which Torklift Glowstep would be correct for you. If the entry height is between 25-1/2 inches and 36 the part # TLA8103 would be correct. Here are the other height ranges if this doesn't work for you.
18-1/2" - 28" # TLA8102
25-1/2" - 36" # TLA8103
32-1/2" - 44" # TLA8104
39-1/2" - 52" # TLA8105
46-1/2" - 60" # TLA8106 view full answer...
While your Grand Design Imagine 21BHE is lighter weight it does weigh more than half the weight of your tow vehicle so a weight distribution system will be a great idea and I would recommend you go with one. You'll have better ride quality, handling, and braking so it will be worth it. Based on the weights you mentioned the Fastway kit you are wanting part # FA94-00-0800 would work really well so that would be a solid choice as well. view full answer...
For your Grand Design Transcend 29TBS the slide topper I recommend for your 118 inch flange to flange measurement is the Solera 10.5' Slider (Slide-Topper) in Black w/ Black Hardware # LCV000182037. This slide topper is designed for a box width from flange to flange of 116 to 121-3/4 inches. This will fit your slide out perfectly.
It is also available in white with white hardware # LCV000163293. These awnings come with all the awning rail included. view full answer...
The Voyager WiSight 2.0 Wireless Backup Camera System # ASA37YR is only going to be compatible with similar rear facing cameras like part # ASA74YR. You can place these on the sides but they aren't the best compared to the design of other options on the market. Personally, I recommend either the # FCE48TASL-05 if you aren't replacing a rear clearance light or the # FR98NR if you will be tapping in at the light.
I've attached a couple of videos below to help walk you through the installation... view full answer...
You're looking for the Dexter E-Z Flex Suspension Kit - Double-Eye Springs - Tandem Axle - 6,000 lbs # K71-652-00, which will fit on tandem axle trailers with 33" spacing between the axles (measured center on center of the axle-as you did). This is a complete equalizer upgrade kit that comes with cushioned equalizers, shackle straps, wet bolts and bushings you'll need to upgrade from your standard equalizers.
I've linked a review and installation video of this kit for you to check out, as well. view full answer...
The Multi-Fit Motorhome Trailer Hitch # 5350 is designed to fit a frame width of 24" - 46". To know if this adjustable hitch is going to fit your 2019 Grand Design Transcend Travel Trailer you'll have to measure the distance between the inside of the frame beams.
If you have a larger frame distance than 46" then we also have the Adjustable Width Trailer Hitch Receiver for RVs # 13703, which fits frame widths 22" to 72". view full answer...
Based on your 2020 Grand Design Transcent 265BH's current # TREQ104 equalizers and 33" wheelbase I recommend going with the MORryde CRE3000, as in my opinion it's a better design of an equalizer that does a better job of preventing bumpiness going from the road to the trailer than the Dexter EZ-Flex.
For your trailer you'll need the following components:
MORryde Rubber Equalizers # MR87ZR
MORryde Suspension Upgrade Kit # MR58ZR
This is not too bad to install yourself assuming you have... view full answer...
From what you described it sounds like you're needing the T-Fitting # 103602-MBS along with the Fill Hose # 100019-144 (for your small tank), the Tank Connector # 204037-MBS, and the 2-Stage Propane Regulator # 108221. Attached is a photo of what this setup looks like and below is a full list of the parts you'll need if all you currently have is the 100 lb tank:
T-Fitting - # 103602-MBS
Fill Hose - # 100019-144
Adapter Hose - # 100284-144-MBS (for an appliance like the Grill # FR51322)
Tank... view full answer...
Since you have the 69 inch arms the correct support arm replacement is the part # LC281154. The part number you mentioned would be correct for the 63 inch arms. view full answer...